Four hours today, to work on things that are not specifically mentioned on the plans. We cut, glued and screwed 8 additional supports for the sole panels at the bulkheads corners. Two of those are visible in the photo below
We had prepared the daggerboard trunk for the glue up but the resin went off in a very short time so we had to throw away a fairly sized blob. Next time...
Total work time to date: 278 hours
Saturday, May 9, 2015
Saturday, May 2, 2015
Daggerboard trunk glassing
May 1st is a holiday over here so we could work (a bit) also on friday morning. We spent 4 hours between friday and saturday to glue the trunk spacers and to glass both faces.
Here's Cinzia cutting the fiberglass cloth (160 grams per square meter) to size with special fiberglass scissors.
Here's the first side glassed. There's one single piece of fg going all the way from the top of one spacer to the top of the other. That's why the upper corner is rounded, while we made a fillet on the other. Other then glued, the trunk sides are also nailed to the spacers with bronze ring nails.
And here's the other side glassed as well. We also glued the extension to the forward sole (which as you know came out short due to an error in the plans).
Total work time to date: 274 hours.
Here's Cinzia cutting the fiberglass cloth (160 grams per square meter) to size with special fiberglass scissors.
Here's the first side glassed. There's one single piece of fg going all the way from the top of one spacer to the top of the other. That's why the upper corner is rounded, while we made a fillet on the other. Other then glued, the trunk sides are also nailed to the spacers with bronze ring nails.
And here's the other side glassed as well. We also glued the extension to the forward sole (which as you know came out short due to an error in the plans).
Total work time to date: 274 hours.
Sunday, April 26, 2015
Daggerboard trunk (2)
Two more hours to cut and rip all pieces necessary to build the daggerboard trunk. As you can see in the pictures, the framing lumber is pretty thick so this is likely to be the strongest piece of the whole boat.
This view shows the bottom side, framed in 2x4s which will be glued and screwed to the bottom
while this shows the upper part which will be glued to the low side of the sole.
Total work time to date: 270 hours
This view shows the bottom side, framed in 2x4s which will be glued and screwed to the bottom
while this shows the upper part which will be glued to the low side of the sole.
Total work time to date: 270 hours
Daggerboard trunk (1)
The construction and subsequent installation of the daggerboard trunk is described both on the plans and in the instructions. As already happened, though, there are several ambiguities: first of all, the plywood thickness is specified to be 1/4" (6 mm) on the plans and 1/2" (12 mm) in the instructions. We decided to use the 3/8" (10 mm) plywood. Also the installation sequence is pretty different in the two sources. So we spent quite some time studying the drawings and reading the instructions, and will probably develop our own sequence.
On saturday morning we spent a couple of hours studying the plans and cutting the pieces for the daggerboard trunk. Here are the two sides made of 10 mm plywood
and here the sides with the two spacers in between
Total work time to date: 268 hours
On saturday morning we spent a couple of hours studying the plans and cutting the pieces for the daggerboard trunk. Here are the two sides made of 10 mm plywood
and here the sides with the two spacers in between
Total work time to date: 268 hours
Thursday, April 23, 2015
Back at it
Here we are again after one idle (boatwise) month. Just one hour yesterday to adapt the aft floor panel to the boat. The photo shows the cutting line: the original panel was drawn according to the dimensions shown on the plans but there was no way to force it into the hull both lenghtwise and widthwise.
Total work time to date: 266 hours
Total work time to date: 266 hours
Friday, April 10, 2015
Update
Not much done lately. During the Easter period Cinzia went away for a sailing week, and the weather at home was so miserable and cold that the shop was very uncomfortable to work in.
Now we both are in Vienna for a conference and will be back in a week or so. But we do think about the boat all the time!
Now we both are in Vienna for a conference and will be back in a week or so. But we do think about the boat all the time!
Saturday, March 28, 2015
Fitting the sole panels
Four hours today to fit the ill-sized sole panels...
This is a real pain in the a** because we trusted plans and instructions but the dimensions proved wrong. We should have checked on the hull before cutting plywood. Here's a view that shows the real error in length (the tape measure is metric) in the forward panel, which we had previoulsy cut according to the plans)
This photo shows another issue. See that resin fairing below the butt block? The instructions suggest to leave that space empty so that you can insert the corner of the panels there. but there's no way to persuade 10 mm thick plywood to do that thing, so we decided to fill those spaces with thickened resin and then cut recesses in the corners of the sole panels. In this specific case we also have to glue a butt block under the sole and then add an extension to reach the bulkhead.
The last pic shows the central sole panel, whose length was almost there while the width was way off at the bulkheads. Same as above regarding the recesses at the corners.
This panel is important because it will be the cockpit floor through which the daggerboard goes: its trunk stays between sole and floor.
We started to work also on the aft sole panel, which is both too long (by about 2 cm) and too wide at the bulkhead. Will finish next time.
Total work time to date: 265 hours
This is a real pain in the a** because we trusted plans and instructions but the dimensions proved wrong. We should have checked on the hull before cutting plywood. Here's a view that shows the real error in length (the tape measure is metric) in the forward panel, which we had previoulsy cut according to the plans)
This photo shows another issue. See that resin fairing below the butt block? The instructions suggest to leave that space empty so that you can insert the corner of the panels there. but there's no way to persuade 10 mm thick plywood to do that thing, so we decided to fill those spaces with thickened resin and then cut recesses in the corners of the sole panels. In this specific case we also have to glue a butt block under the sole and then add an extension to reach the bulkhead.
The last pic shows the central sole panel, whose length was almost there while the width was way off at the bulkheads. Same as above regarding the recesses at the corners.
This panel is important because it will be the cockpit floor through which the daggerboard goes: its trunk stays between sole and floor.
We started to work also on the aft sole panel, which is both too long (by about 2 cm) and too wide at the bulkhead. Will finish next time.
Total work time to date: 265 hours
Subscribe to:
Posts (Atom)












